In order to play game audio, a wireless headset must be "paired" to its transmitter. The headset and transmitter are paired out of the box. The instructions below are only necessary if pairing appears to have been lost. This can happen if the headset is turned off for a long time or is out of range.
When the headset and transmitter are paired, the transmitter's Power/Pairing LED will be solid. If this LED is "blinking" slowly (slowly fading in and out), it means the transmitter is not paired with the headset and game audio will not play through the headset.
The Transmitter sends game audio only. Chat is handled through the console directly via bluetooth(PS3) or through the controller (Xbox 360, PS4). Chat audio is not an indicator that the headset is paired to the transmitter.
NOTE: The instruction book that comes with some headsets does NOT mention that you have to keep holding down the button on the headset to hear a second set of two beeps.
Tips before you begin:
- Make sure your headset has enough battery power. Either let your headset recharge for several hours, or install a fresh set of batteries in your headset. When battery power is low, the headset will not pair properly.
- Make sure the headset and transmitter are 2 to 3 feet apart (about an arm's length) when pairing. If they're right on top of one another, they will not pair properly.
1) Turn off the headset by pressing the headset Power button for 3 seconds. The LED on the headset should be completely off when it is powered down.
2) Unplug the transmitter's USB power cable to power it down. Wait 3 seconds and then plug the power cable back in. The transmitter's Power/Pairing LED should now be pulsing slowly on and off.
3) Hold down the transmitter's Pair button for about 5 seconds. Release the Pair button when the transmitter's Power/Pairing LED begins to flash rapidly (twice per second). It should now be blinking quickly and steadily twice per second. If it is blinking much more than 2 times per second, the button was held for much too long (15+ seconds), and you must start over from Step 2.
4) With the headset still powered off, hold down the headset's Power button for about 6 seconds until you hear a second set of two beeps. The headset's Power LED should now be blinking rapidly like the transmitter (twice per second). The LED should not be double blinking (two quick blinks followed by a pause). If it is double blinking, then the button was not held long enough, and you must start over from Step 1.
5) Wait about 10 to 15 seconds. The transmitter's Power/Pairing LED should be solid, and the headset's Power LED should now be flashing steadily once per second.
The headset is now paired to the transmitter and is ready to play game audio.
Notes for PX4, XP300, XP400 & X-Ray:
- You will hear two beeps (headset on), followed by three ascending beeps (Bluetooth on), then the second set of two beeps (pairing headset). Make sure you continue to hold the power button on the headset down until you hear the final two quick beeps.
- Do not hold down the TONE button while powering on the headset; if you do, the power LED will blink extremely quickly and you will have to start over from Step 1.
* * * * * * * * * * * * *
How do I know if my headset and transmitter are in pairing mode? (X32, X42, PX4, XP300, XP400, X-Ray)
The transmitter has three different "flashing" patterns. It can be "Pulsing" on and off, which indicates that it is not paired. If you hold the PAIR button for 5 seconds, it will start blinking 2 times a second at an even rate. This is pairing mode.
If you hold the button upwards of 15 seconds, it will start blinking extremely quickly and the transmitter will leave pairing mode. This is not the correct pairing mode. Unplug the transmitter's USB cable if it's gone this far to "reset" the transmitter.
For X32, X42: The headset plays a couple of alerts. It will beep twice when it first turns on. Keep holding the power button when the headset powers on and you will hear a final set of two identical beeps (high high), then the power LED will start flashing on and off twice per second. This means the headset is in pairing mode. The headset's pairing mode blink is about the same rate as the transmitter's pairing mode blink. NOTE: if the LED is double blinking (two blinks then a pause), the power button was not held down long enough.
For PX4, XP300, XP400, X-Ray: The headset plays several different alerts. It will beep twice when it first turns on. Keep holding the power button when the headset powers on and you will hear three ascending tones, indicating that the bluetooth is turning on. Continue to hold the power button on the headset until you hear a final set of two beeps. The last two beeps indicate that the headset is in pairing mode. When in Pairing mode, the LED on the headset will blink at a quicker pace.
When the headset powers off, it plays two descending tones (high low).
* * * * * * * * * * * * *
The headset Power button is located on the left ear cup, near where the microphone is attached.
The Pair button is located on the side of the transmitter, and the Power/Link LED is on the front.
Power/Link LED is pulsing slowly = Not paired
Power/Link LED is blinking quickly = Pairing mode
Power/Link LED is solid = Paired
If the headset is paired and game audio is still not working, double check that all the connections are secure and plugged into the appropriate ouputs according to the headset's user guide. For further troubleshooting, please contact our Tech Support Team: Contact Support
All files and documents are offered on an *AS IS* basis and you assume full responsibility for using them.
Go to Downloads for User Guides, Drivers, Firmware and other Documentation.